waterpump holder SARASOTA waterpump holder thin wrench -- mmk4mkt

Gauge Holder 37.00
Dial Gauge Holder P240 Used to properly measure crank shaft flywheel and pulley end play.Can also be universally to check clearances and run out.Applicable: Most Porsche and VW air cooled engine.
read more:

Professional Engine Holder Complete 550.00
Engine Holding Fixture Designed to securely carry the entire weightof a fully dressed air cooled twin turbo Boxer 6.Engine Holding Fixture will allow a full 360 degree rotation of engine,with Flywheel Lock allowing for R&R of engine.Bolts up to every Porsche and VW air cooled Boxer ever produced.From Type 1 up to 3.6LItems included in this kit are: P201, VW313 and VW215.
read more:

Civic Counter Holder 79.50

Honda Factory Style Holder Needed to properly counter the rotation of the crank shaft pulley/harmonic balancer during R&R of crank bolt.Comes complete with the proper 2.5 foot long securing bar. Applicable: Model Civic 1980 and Newer.Comes as shown with an adjustable locator lack pin and a 2.5 ft long securing bar, which locks onto the head. See Master Kit for more...(number H070)

Counter Holder Bonus Kit 145.00

Special kit for the professional Honda Acura Technicians2.5 foot long Securing bar. Used to properly counter the rotation of the crank shaft pulley harmonic balancerduring R&R of crank bolt. Honda and Acura models,90 and newer with a 50mm hex slot in crankshaft puller harmonic balancer.and Civic, 80 and newer.

Honda / Accura Counter Holder 79.50

HO50 applicable Honda and Acura models 1990 and Newer
with a 50mm hex slot in crank shaft pulley harmonic balancer.

Mini Bit Holder and Set 10.50

Nice Mini Ratchet Bit Set.
These are mainly Tamperproof bits in this set.
THE SEVEN BITS ON THE LEFT SIDE OF THE SET ARE "TORX TAMPERPROOF)
Plus this set has a number 1 and 2 Phillips bits
Plus a flat head bit.
The Torx sizes are: T10, T15, T20, T25, T30, T40
The Torx have a hole in the tip (tamperproof).

Socket Holder Set 3 9.99

3 Piece Socket Holder SetUsed for holding sockets sizes: 1/4", 3/8 and 1/2"

Bar and Pin for 5 Valve 139.50

Camshaft Timing Tool Set (2)
TOOL REF 3391
Cam/Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 2002 4 cam.

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6Please note: 3391 for 5 valves per cylinder.

BigMak Timing Kit 196.00

Master Kit
Set of 6 Tools
Including Dial Indicator

Set Includes:
3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: Volvo and VW / Audi diesels Excluding TDI
PLUS: VA6015 Holder used for accurate adjustment of Bosch diesel injection pump.
Plus: 2065A Diesel Camshaft Locking Plate Tool
PLUS: 2064 Lock Pin for Diesel.
Plus the Pin Wrench (made in Germany) for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys with Pin holes. This wrench with its protruding pins, grabs the center of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment. Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80.
Plus Dial Indicator

Cam Bar and Pin for 2 Valve 139.50

Camshaft TimingTool Set (2)
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4  94 97 AFC Engine

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6

Please note: 3243 for 2 valves per cylinder. 

Cam Bar for 2 Valve 129.50

Camshaft Securing Bar Timing Tool
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4 94 97 AFC Engine
Please note: 3243 Securing Bar for2 valves per cylinder.

Cam Bar for 5 Valve 129.50

Camshaft Timing Tool Securing Bar
TOOL REF 3391
Cam Securing Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 (2002 4 cam)
Please note: 3391 for 5 valves per cylinder.

Counter Holder 125.00

Counter Holder Original Factory Tool made in Germany

Counter Holder 0.00

3415 USED TO COUNTERHOLD CRANKSHAFT TOOTHED BELT SPROCKET WHEN RENEWING CRANKSHAFT OIL SEAL.
Factory Tool Made in Germany.
Call or email for availability.

COUNTER HOLDER 97.50

COUNTER HOLDER 3248A
USED TO REMOVE AND INSTALL THE VIBRATION DAMPER. USED FOR VEHICLES WITH POLYRIBBED BELTS

Crankshaft Pulley Tool 84.50

Crankshaft Tool 2084 Counter Holder Used for R & R of Front Crankshaft PulleyApllicable: VW Audi with 5 Cylinder.80, 90 Quattro, 400, 5000 QuantumUsed in conjunction with tool 2079

Dial Gauge Holder 37.50

Dial Gauge Holder VA6015Diesel Tool Used for accurate adjustment of Bosch diesel injection pump. (SAME AS VW TOOL 2066)
This Dial Gauge Holder screws into the back of theinjection pump and comes equipped with a 10cm dial indicator extension pin. This tool is to be used in conjunction with a dial indicator (not included).All VW Audi diesel and Volvo D24 6 cylinder 2.4L diesel 1981 86 engines. This holder will only work with a dial guage with a shank size of 8mm or less.
It will NOT work with a larger shank.

Dial Indicator and Holder 98.50

Bosch Diesel Injection Pump
Timing Indicator Tools.
With High Quality Dial Indicator Made in Germany!
You will not find this price anywhere except Zdmak!
Tools are used for the accurate setting of
the Bosch diesel fuel injection pump timing.
The Holder screws into the back of the injection pump,
giving a dial indicator reading necessary for setting
the correct pump timing.
This set comes complete with the correct tools for the job!
Contents: Metric Dial Indicator Made in Germany,
plus holder plus the 10cm dial indicator extension pin,
making the timing easy to set,
as the timing has a range from 0.83mm to 1.15mm.
For use on VW and Audi diesels.
Also works with 1981 1986 Volvo 6 cyl 2.4L diesels,
1989 1994 Dodge 6 cyl 5.9L diesels.

FYI FOR PEOPLE WHO DECIDE "NOT" TO USE THIS SET
Here is some helpful info...Universal conversion factor for milimeters into decimal inches is .03937
EXAMPLE: 13mm X .03937= .5118"

Front Crankshaft Pulley Set 187.50

Crank shaft pulley Set of 2 tools:VW 2084 & 2079Counter Holder 2084needed for R&R of front crank shaft pulley. ApplicaTIONS for 2084: VW/Audi models with 5 cylinder engines 80, 90, Quattro, 4000, 5000, Quantum.Used in conjunction with Extension Wrench 2079 BELOW. PLUS: 2079 Extension Wrench needed for R&R of front crank shaft bolt.ApplicablE: VW/Audi models with 5 cylinder engines80, 90, Quattro, 4000, 5000, Quantum.

Locking Pin , Plate , Holder , Pin Wrench 77.00

Set of four tools: VA6015 PLUS 2065A PLUS 2064 PLUS 12717

New Ball Torx Set 29.99

Another ZDMAK Special!
ZDMAK offers the first Ball Drive Torx Bits!
Made of Super S2 Steel, the strongest and hardest bits available.
Ball Torx Set T10 thru T50
TORX is a registerd trademark of the Camcar Corp.
11 piece set, 9 Ball Torx Bits & 2 bit drivers.
Ball Torx sizes, T10, T15, T20, T25, T27, T30, T40, T45 and T50.
Ball head to reach fasteners in difficult locations.
Includes magnetic bit holder and magnetic bit driver.

Pin , Plate and Holder 64.00

Set of three tools including:VA6015 Diesel ToolUsed for accurate adjustment of Bosch diesel injection pump.This Dial Gauge Holder screws into the back of theinjection pump and comes equipped with a 10cm dial indicator extension pin. This tool is to be used in conjunction with a dial indicator.(not included).Applicable:All VW/Audi Diesel and Volvo 6 cylinder 2.4L diesel '81 '86 engines. PLUS 2065A Diesel Cam Shaft Locking Plate 2065aPLUS 2064 Locking Pin

Power Steering Waterpump Pulley Tool 24.00

VA6024Power Steering and Waterpump Pulley Removal & Replacement Tool Volkswagen AudiUsed to hold the power steering or water pump pulley stationarywhile removing or replacing the three socket headbolts that attach pulley to the shaft.Tool is designed to be used on pulleys that utilize these socket head bolts.Applications:VW Audi 4 cylinder water cooled gas or diesel engines from 1975 to current.Volkswagen V6 1992 and newer.Audi power steering pump pulley V8 1990 and newer.Audi V6 1992 to current.Also VW 1983 to 1988 and Audi 1981 to 1995 with socket head boltsholding the pulley to power steering pump.

Puller, Pin , Plate , Holder , Pin Wrench 146.00

Set of five tools: vw 3032, VA6015 PLUS 2065A PLUS 2064 PLUS 12717
Details:
3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: Volvo and VW / Audi diesels Excluding TDI * PLUS: VA6015 Used for accurate adjustment of Bosch diesel injection pump. PLUS: 2065A Diesel Camshaft Locking Plate Tool PLUS: 2064 Lock Pin for Diesel. Plus the Pin Wrench (made in Germany) for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys with Pin holes. This wrench with its protruding pins, grabs the center of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment. Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80.

Pump Tool plus Pin , Plate and Holder 127.99

Set of 4 tools including:3032 Injection Pump ToolPuller used for the proper extraction of injection pump drive gear.Applicable: Volvo and VW / Audi diesels Excluding TDI * PLUS: VA6015 Used for accurate adjustment of Bosch diesel injection pump.PLUS: 2065A Diesel Camshaft Locking Plate Tool PLUS: 2064 Lock Pin for Diesel

Magnetic Bit Holder 00
Magnetic bit holder with handle. The magnetic blade retains the bit and the screw at the same time.
read more:

Ratcheting Bit Holder 0.00
Reversible ratchet double ended for bits.Overall length 140mm for 1/4 and 5/16 sizes.

read more:

Set with Magnetic Bit Holder and Case 00
Item861PE/S9DescriptionSet of 8 hexagon bits with magnetic bit holderSpecificationsThe plastic pocket bit holder can be used as handle.
read more:

SLIDE HAMMER 0.00
Item1540DescriptionSliding hammer, galvanizedSpecificationsTo be used with legs 1543 (with leg holder 1543S) and extractors 1544.
read more:

Sure Grip Magnetic Bit Holder 00
Magnetic bit holder with bi material handle.
read more:

The Beta Tank Tool Trolley 00
ItemCX25DescriptionTank trolley with compartmentSpecificationsMain features:Foldaway lid.1 sliding drawer.Tool tray protected by foamed rubber mats.Shelves protected by oil and fuel proof mats.Four castors 0 100 mm in 0:2 fixed and 2 swivelling (one with brake).Safety lock.One more shelf M4 can be added on the opposite side.Thermoformed tray for 1/2' sockets and accessories.Paper roll holder item 2499PC can also be included.Lower compartment, 290 mm high with 2 safety locks.Locking system of the lids in the open position.
read more:

Two Leg Puller 00
Item1542DescriptionTwo leg pullers, galvanizedSpecificationsA threaded hole in the pulling screw makes it possible to fit legs 1543 (by leg holder 1543S) and extractors 1544.For pulling, lock the screw and turn the nut.
read more:

BMW Daily Double 27.50

Daily Double!
Two Tools
Including Item Number BMW3022: Radio Removal Tool.Pentagon shaped tool with 3 5/8 inches overall length.Applicable: Most BMWs.This Five sided driver is used to release anti theft radio mounts.
Plus the two sided counter holder. More details about this tool number BMW 1703 Waterpump Tool
This special tool covers most popular applicationsUsed for securing Water Pump Hub from rotating during R & R of Fan Clutch NutApplicable:M10, M20, M30, M40, M41, M42, M50, M52, M60, M62 (1703 should be used in conjunction with a 32mm or a 36mm thin wrench). Picture is not to scale.

BMW Flywheel Lock 66.99

FACTORY FLYWHEEL LOCK 112170
Holder for locking flywheel with transmission installed.
Applicable: BMW M20, M21, M40, M41, M42, M43, M44, M50, M51, M52, S50, B30, B32

BMW Holding Tools 63.00

Set of 2 Repair ToolsIncluding: Thin Wrench Number 1032X36TThis Wrench is 32 X 36mm with an 8mm thicknessand an overall length of 12 inches for proper leverage.Many applications for this handy thin wrench.PLUS: Counter HolderUsed for securing the waterpump hub from rotatingduring R & R of fan clutch nut.Applicable: Engine M40, M41, M42, M60, M62SET NUMBER BMW3632 3037

BMW Holding Tools 59.99

Set of 2 Repair ToolsIncluding: Thin Wrench Number 1032X36TThis Wrench is 32 X 36mm with an 8mm thicknessand an overall length of 12 inches for proper leverage.Many applications for this handy thin wrench.PLUS: Counter Holder 3008Used for securing the waterpump hub from rotatingduring R & R of fan clutch nut.Applicable: M10, M20, M30, M50 with 32mm clutch nutSET NUMBER BMW3632 3008

Counter Holder 3008 37.50

Counter HolderWATERPUMP HUB TOOL BMW3008 Holder used for securing the waterpump hub from rotatingduring R & R of fan clutch nut.APPLICABLE M10, M20, M30, M50, WITH 32MM CLUTCH NUT.

Counter Holder 3037 37.00

Counter HolderBMW 3037 Holder used for securing the waterpump hub from rotatingduring R & R of fan clutch nut.Applicable: Engine M40, M41, M42, M60, M62

Counter Holder Head 0.00

Counter Holder Head
Once the crank bolt is removed, the second phase of the task of extracting the sometimes stuck vibration damper by using tool numbers BMW 3050 2 in conjunction with BMW 3050 3 Applicable: BMW Engine M52TU, M54, M56.

Counter Holder Tool 0

Counter Holder Tool used to make the difficult task of breaking loose the harmonic balancer / crank shaft bolt EASY by using tool numbers BMW 3050 1 in conjunction with 3050 2.

Double Holder Tool 24.50

Double Waterpump Tool*
This special tool covers most popular applications
Used for securing Water Pump Hub from rotating during R & R of Fan Clutch Nut
BMW engines:M10, S14, M20, M21, M30, S38, M40, M41
M42, M43, M44, M50, M52, M60, M62, S50
Should be used in conjunction with a 32mm or a 36mm thin wrench.

Hex Bit Driver 9.50

Hex Bit Driver Finger Stubby 1/4 inch Hex, 1/4 inch Sq.Dr. chrome holder (bit not included).

Hex Bits and Magnetic Holder 3.99

Set of 7 (Including 6 Hex Bits plus case.)
GREAT FOR WORKING ON GERMAN CARS!
Quality alloy steel bits (6) plus Magnetic quick change bit holder.Convenient mini storage case bit selectorHex Bits sizes: 2,2.5,3,4,5,6mm
Picture is for reference only.
THESE ARE ALL HEX BITS
Do not buy this item if you are NOT looking for hex bits.

Holding Tool & 32mm Wrench 39.99

Set of two tools for BMW Repair Includes:
Double Waterpump Tool. This special tool covers most popular applications
Used for securing Water Pump Hub from rotating during R & R of Fan Clutch NutApplicable:M10, S14, M20, M21, M30, S38, M40, M41M42, M43, M44, M50, M52, M60, M62, S50

Plus Long Pattern "Thin Wrench" 32mm Open End.
What makes this set different from other sets you will see is the 32mm wrench. This is a heavy duty tool and 20 inches long.
No one else has a set like this for the price. The 32mm is a WHOPPER.

Holding Tool and 36mm Wrench 39.99

SET OF 2 Includes:
* Double Waterpump Tool*
This special tool covers most popular applications
Used for securing Water Pump Hub from rotating during R & R of Fan Clutch Nut
Applicable:M10, M20, M30, M40, M41, M42, M50, M60, M62

Plus
Long Pattern Thin Wrench

Size: 36mm Open End.

Holding Tool and Wrench Set 49.99

Set of 3 Includes:
Double Waterpump Tool*
This special tool covers most popular applications
Used for securing Water Pump Hub from rotating during R & R of Fan Clutch Nut
Applicable:M10, M20, M30, M40, M41, M42, M50, M60, M62

Plus
2 Long Pattern Thin Wrenches
German Car Special Tools
One of each size: 36mm and 32mm
Overall length of 15 inches.
Thickness of each wrench is 8mm.

Impact E Torx Set 23.50

Impact E Torx
Female Socket Set 7Pc
Sizes included: E6, E7, E8, E10, E12, E14 & E16
Packaged in a in red vinyl holder.

Impact Quality S2 Bit Set 9.50

Impact Quality S2 Bit Set, 8pc Bits 5/16" Hex bodies, 1.25"L, P1 P4 Phillips & 1/4", 5/16", 3/8", 1/2" Flat Bits, Plastic Holder

Mercedes and BMW Set 89.50

ON SALE 7 Pc Benz and BMW Tools Including 4 Mercedes Tools a BMW Holding Tool plus 2 Thin Wrenches.
Benz Tools are:
1.Hub Securing Bar 113 0040 Used for securing Waterpump hub from rotating during R&R of Fan clutch nut. This holder bolts onto the hub, as the poly v belt is not in place and cannot be used to lock the hub. Applicable:M112 & M113

2.Locking Hook needed for securing the visco fan couplingduring R&R of 8mm hex fastener w/o removing the radiator: Mercedes M103.

3.Wrench / Holding Bar. This is similar to Benz Number 900 589 0307 00 Comes complete with 8 and 10mm Allen bits.The 8mm is needed for R&R of fan clutch fastenerApplicable M103, 104, 111, 119, 120 OM 602, 603, 605, 606The 10mm is used for adjusting A/C belt tension and R&R of idler pulleyModels 420, 560 with V 819 86 and Newer
4. Thin Wrench 65mm with an 8mm overall thickness and an overall length of 16 inches for proper leverage. Mercedes ref: 120 589 0201 00

BMW Double Waterpump ToolThis special tool covers most popular applications used for securing Water Pump Hub from rotating during R & R of Fan Clutch NutApplicable:M10, M20, M30, M40, M41, M42, M50, M60, M62

Metric Ball Hex Set 13.50

Metric Ball Hex Set 11 Pc
1.5mm thru 8mm ball hex bits, VI10 magnetic driver & 1/4" hex X 1/4" Sq.Dr. chrome bit holder in blue plastic box.

You Searched for

waterpump holder

Trade Links With ZDMAK