Belt Tension Guage SARASOTA Belt Tension Guage vw head bolt tool -- mmk4mkt

End Play Kit 00
This tool has isdesigned to measure the end play movement
of the VW crankshaft without the use of a dial indicator.
All that is necessary is a feeler gauge set and this tool.
With the tool bolted to the end of the case, the feeler guage
measures the gap created by the end play.
The taking of this end measurement is necessary whenever a VW engine is rebuilt
to prevent the rear main bearing from seizing up.
A must for rebuilding one engine or many,
this tool works on all air cooled VW engines and Porsche 912 & 914 models.
read more:

Cam Spoke Lock Device 79.00

Twin and Quad Cam Spoke Lock Device
Universal Twin Cam Number 2727Used for securing Twin Cam Pulleys.
Applicable: All twin or quad cam engines with timing belt pulley sprocket on each cam.Used for the crucial task of securing twin cam pulleys from rotating during the R&R of timing belt. Fully adjustable, this tool comes complete with 1 pair 8" and 1 pair 4.5" long, Left/Right hand threaded rods.The shorter needed for confined spaces where the rods might interferewith the fire wall or other auto part. Fully constricted onto the spokesof the cam pulleys and locking down the securing wing nuts,reveals a 6 point locking mechanism.This tool will remain rigid, not allowing for any movement of cams, saving your timing.Please note:With Quad cam pulley engines 2 sets of tool 2727 are needed to complete the task.All Twin or Quad cam equipped with a timing belt pulley sprocket on each cam.

Crank Belt Puller 32.99

Crank Shaft Pulley Belt Puller TOY 135 Puller needed for the proper extraction of pulley from crank shaft. Applicable: Toyota model Cressida and Supra 82 1988 with 5MGE engine.

Digital Tire Pressure Guage 13.99

Digital Tire Pressure Guage 0 100 PSI range. Measures PSI and BAR 1/4 inch LCD display. Compact design allows for easy storage in glove box, tool box or tool bag, etc...No adjustments necessary. Includes 3V Lithium battery.

Expanding Compressor Kit 35.99

Used to compress and secure the hydraulically activated belt tensioner.This tool presses against a neighboring water pump pulleyand expands as you rotate the 17mm nut.When fully compressed, place locking pin into hydraulic piston push rod.

Metric Feeler Guage 9.99

25 Straight Blade
Feeler Guage Set
Thickness In millimeters
The blades in this guage set are metric sizes.0.04 thru 1.00mm
Excellent for the professional or shadetree mechanic.

Special Open Socket 22mm 25.00

On Sale *
22mm Special TubeSocket
1.) Used for securing the Strut tower retaining nut of most European models (crucial when adjusting tension of front shocks). The 2/3 open side walls of this socket allows for easy access of an adjusting wrench. (normally 7mm Allen Hex Wrench)
2.) R&R of Oxygen Sensor.
Also for R&R of some Mercedes Diesel injectors ( OM604, 605 & 606).
Details: For removing and installing front strut unit on VW Golf up to 1988, Jetta up to 87, Scirocco, Audi 80 and Golf 3 from 1993 newer, Passat from 88 and newer, Audi 100, 200 Coupe and Quatro.
This tool is often used in conjunction with a 7mm hex wrench.
Clickhere for a picture of the tools in action: 

Torque Angle Guage 14.99

Torque Angle Guage 1/2 inch Drive
Measures angle of rotation after pre torque load in torque angle applications.
360 degree scale clearly marked in 2 degree increments and intervals of 10 & 30.
Easily zero the gauge by turning housing for next application.

19mm Suspension Strut Socket 59.95

Special 19mm Tube SocketUsed for securing the Strut tower retaining nut of select European models (crucial when adjusting tension of front shocks). The 2/3 open side walls of this socket allows for easy access of an adjusting wrench. (normally 7mm Allen Hex Wrench)For removing and installing front strut unit on VW Audi 19mm nut.This tool is often used in conjunction with a pin wrench / allen wrench or both.

2 Piece Socket Set 32.99

22mm Special Tube Socket 4491A Plus Pin Wrench VW524
Used for securing the Strut tower retaining nut of most European models
(crucial when adjusting tension of front shocks). The 2/3 open side walls of
this socket allows for easy access of an adjusting wrench.
(normally 7mm Allen Hex Wrench)
Also for R&R of Oxygen Sensor.

VW524 Pin Wrench Socket with 1/2" drive. This tool is used for R&R of
grooved ring retaining nut on strut tower of front shock absorber.
Also used for adjusting power steering gear on VW Jetta, Golf, GTI.

2 Pins and 2 Plates 103.00

2 Pins and 2 Plates Set of four tools.VW Audi T.D.I. and New Beetle Cam Kit Reference numbers for the two tools on the left are: 3418 and 3359. Tool Set for factory correct and trouble free installations. This is a popular set for Diesel timing of Bosch injection pumps. This set has been developed for aligning the cam shaft with the Diesel pump on 1998 and newer VW models equipped with a T.D.I. engine. This two piece lock plate and alignment pin allows the technician for factory correct and trouble free installations.

Tools on the right side of image are Diesel Lock Plate / Cam Setting Bar Same as Volkswagen ref 2065a Tool used for securing the cam shaft from rotating and maintaining correct timing position engine AAZ during R&R of cam shaft drive belt. Applicable: VW/Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 Lock Pin for Diesel (Same as VW tool 2064). Tool used for securing Bosch diesel injection pump sprocket from rotating during R&R of cam shaft drive belt. This Locking Pin also assists in locating the general timing position of pump. Volkswagen Audi diesel and Volvo 6 cylinder 2.4L diesel 1981 86 All 4 tools are High Quality Made in Europe!

21mm Suspension Strut Socket 59.95

Special 21mm Tube SocketUsed for securing the Strut tower retaining nut of select European models (crucial when adjusting tension of front shocks). The 2/3 open side walls of this socket allows for easy access of an adjusting wrench. (normally 7mm Allen Hex Wrench)For removing and installing front strut unit on VW Audi 21mm nut.This tool is often used in conjunction with a pin wrench / allen wrench or both.

22mm Socket plus 7mm Allen Wrench 26.99

2 Piece set
22mm Special Tube Socket 4491A plus 7mm Allen WrenchUsed for securing the Strut tower retaining nut of most European models(crucial when adjusting tension of front shocks). The 2/3 open side walls ofthis socket allows for easy access of an adjusting wrench. (normally 7mm Allen Hex Wrench) (This socket can also be used for R&R of Oxygen Sensor.)
Plus a 7mm Allen Wrench.The Allen wrench is 7mm and is 7.5 inches Long.

22mm Strut O/2 Sensor Socket 18.99

On Sale 22mm Special Tube Socket 1.) Used for securing the Strut tower retaining nut of most European models (crucial when adjusting tension of front shocks). The 2/3 open side walls of this socket allows for easy access of an adjusting wrench. (normally 7mm Allen Hex Wrench) 2.) R&R of Oxygen Sensor.
Also for R&R of some Mercedes Diesel injectors ( OM604, 605 & 606). Details: For removing and installing front strut unit on VW Golf up to 1988, Jetta up to 87, Scirocco, Audi 80 and Golf 3 from 1993 newer, Passat from 88 and newer, Audi 100, 200 Coupe and Quatro. This tool is often used in conjunction with a 7mm hex wrench.Clickhere for a picture of the tools in action:

3 Piece Strut Set 34.99

On Sale! 22mm Tube Socket Plus Pin Wrench number VW524, Plus 7mm Allen Wrench
Tools used for securing the Strut tower retaining nut of most European models
(crucial when adjusting tension of front shocks). The 2/3 open side walls of
this socket allows for easy access of an adjusting wrench.
(normally 7mm Allen Hex Wrench)
Also for R&R of Oxygen Sensor.

VW524 Pin Wrench Socket with 1/2" drive. This tool is used for R&R of
grooved ring retaining nut on strut tower of front shock absorber.
Also used for adjusting power steering gear on VW Jetta, Golf, GTI.

3 total pieces in this set: 2 Sockets and 7mm Allen Wrench.
The Allen wrench is 7.5 inches long.

Adjustment Guage Pack 29.99

Adjustment Guage Pack; USED FOR CHECKING AND ADJUSTING BUMPERS ON HOOD LID AND DOOR SEALS. Excellent for the professional or shadetree technician.

Alternator Socket 27.00

For mounting the V belt pulley (slip clutch pulley) at the alternator (manuals call it a generator),
especially for T.D.I. VW Golf III, Vento, Passat and AUDI A 3
17MM outside dia. Length 30mm.
Also for Boxster. (See repair Group 27 (Porsche Bulletins) Boxster Alternators with free wheeling Pulleys. High Quality Tool
Made in Germany.
This 3400 is Hazet number 2592.

Bar and Pin for 5 Valve 139.50

Camshaft Timing Tool Set (2)
TOOL REF 3391
Cam/Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 2002 4 cam.

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6Please note: 3391 for 5 valves per cylinder.

Belt Tension Guage 54.50

Belt Tension Guage Special Tool used to adjust the tension on the cam belt where the movement of timing belt is measured by load (NM). Suitable for use on cam belts various belt widths. Easy to use. Clear incremental marking with knurled knob for precise measurement. Dual scale allows reading from top or bottom of tool.

BigMak Timing Kit 196.00

Master Kit
Set of 6 Tools
Including Dial Indicator

Set Includes:
3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: Volvo and VW / Audi diesels Excluding TDI
PLUS: VA6015 Holder used for accurate adjustment of Bosch diesel injection pump.
Plus: 2065A Diesel Camshaft Locking Plate Tool
PLUS: 2064 Lock Pin for Diesel.
Plus the Pin Wrench (made in Germany) for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys with Pin holes. This wrench with its protruding pins, grabs the center of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment. Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80.
Plus Dial Indicator

Cam Bar and Pin for 2 Valve 139.50

Camshaft TimingTool Set (2)
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4  94 97 AFC Engine

TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
For installing or removing toothed belt /flywheel drive plate.
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6

Please note: 3243 for 2 valves per cylinder. 

Cam Bar for 2 Valve 129.50

Camshaft Securing Bar Timing Tool
TOOL REF 3243
Cam/Bar Holder 2 valves per cylinder/
Used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during belt change head assembly work.
Applicable Audi 90 A6 A4 94 97 AFC Engine
Please note: 3243 Securing Bar for2 valves per cylinder.

Cam Bar for 5 Valve 129.50

Camshaft Timing Tool Securing Bar
TOOL REF 3391
Cam Securing Bar Holder
V6 / 5 valves per cylinder/
used for the crucial task of securing both engine banks/
camshafts at T.D.C when replacing the timing belt/
to properly align camshaft during timing belt change /head assembly work.
Applicable VW Audi V6 5 Valve 1998 2003
Cam/Bar Holder Not Applicable 3.0 (2002 4 cam)
Please note: 3391 for 5 valves per cylinder.

Cam Shaft Locking Plate 16.99

Cam Shaft Locking Plate 2065AUsed for securing the cam shaft from rotatingand maintaining correct timing position during R&R of cam shaft drive belt.All VW Audi Diesel and Volvo D24 6 Cylinder 2.4L diesel 1981 86 engines.

Chain Adjuster 24.50

3366CHAIN ADJUSTER Required to change the troublesome cam adjuster seal
Audi and Volkswagen 4, 6 (2.7 and 2.8) and 8 CylWith 5 Valve per Cyl.
Also Audi VW 1.8 Golf Jetta Passat New Beetle
Note:The manual says to remove both camshafts to change the seal ...
but using this tool you can relieve the tension on the camshaft chainand lift it up far enough to clean, remove and replace the gasket and seal.
This procedure not only saves time but saves any other damagethat may happen to camshafts and bearings by removing them.
ORIGINAL MATRA FACTORY TOOL MADE IN GERMANY

Counter Holder 0.00

3415 USED TO COUNTERHOLD CRANKSHAFT TOOTHED BELT SPROCKET WHEN RENEWING CRANKSHAFT OIL SEAL.
Factory Tool Made in Germany.
Call or email for availability.

Dial Gauge Holder 37.50

Dial Gauge Holder VA6015Diesel Tool Used for accurate adjustment of Bosch diesel injection pump. (SAME AS VW TOOL 2066)
This Dial Gauge Holder screws into the back of theinjection pump and comes equipped with a 10cm dial indicator extension pin. This tool is to be used in conjunction with a dial indicator (not included).All VW Audi diesel and Volvo D24 6 cylinder 2.4L diesel 1981 86 engines. This holder will only work with a dial guage with a shank size of 8mm or less.
It will NOT work with a larger shank.

Drive Belt Sprocket 42.50

NUMBER VA6018Drive Belt Sprocket WrenchLocking wrench used for R&R of drive belt sprocket on cam shaftand drive belt sprocket of intermediate shaft.Applicable: All VW Audi water cooled engines 1974 and Newer.

Hazet Tensioning Tool 75.98

Driving Tool for Tensioning Device
special steel, for operating devicewhen changing the V ribbed belt,especially on VW Polo, Golf and Passat, AUDI since 1991.

Hole Guage 00

Hole Guage
Available two different sizes
ITEM 1707B/1 SIZE: 0.45 TO 1.5
ITEM 1707B/2 size: 1.5 to 3mm

LINKAGE GUAGE 125.00

SHIFT LINKAGE GUAGEUSED WHEN ADJUSTING THE SHIFT AND SELECTOR CABLES ON 02A TRANS
ALSO USED WHEN RETAINING THE GEAR BOX SHIFT LEVER 02A TRANS.3192/1 USED W/3193

Locking Pin 9.50

Lock Pin for Diesel 2064 For securing Bosch injection pump sprocket from rotatingduring R&R of cam shaft drive belt. This Pin also assists in locating the general timing position of pump.Applicable: All VW Audi diesel engines. Volvo D24

Locking Pin and Plate 26.50

Set of two tools including:2065A Diesel Cam Shaft Locking PlateThis locking Plate (above) is the same as vw tool 2065a Used for securing the cam shaft from rotatingand maintaining correct timing position during R&R of cam shaft drive belt.Applicable:All VW/Audi Diesel and Volvo 6 cylinder 2.4L diesel '81 '86 engines. PLUS:2064 Lock Pin for Diesel This Locking Pin is used forsecuring Bosch diesel injection pump sprocket from rotatingduring R&R of cam shaft drive belt.This Pin also assists in locating the general timing position of pump.Applicable: All VW/Audi diesel engines.

Locking Pin Set 3 12.50

Locking Pin Set 3
Made in Germany
TOOLS USED FOR LOCKING OF THE TOOTH BELT TENSIONING COMPONENT. NOTE (ONE SET EQUALS THREE PIECES)

Pin Wrench 37.00

Heavy Duty Tensioner with Handle Grip
Same as Volkswagen number T10020
VW AUDI TENSION PULLEY SPANNER WRENCH This unique tool is for 1998 and later VW and Audi which require spanner wrench adjustments to the timing belt.Details: Special Wrench for adjusting the belt tension on the following: Audi: A6 1.6 (96 and newer) ALZ VW: Polo Classic, Golf, Bora, New Beetle 1.6 (97 ) AEH / AKL / APF / AUR /AVU / AYD Golf, Bora, New Beetle, 2.0 (98 ) AQY / APK

This is the new style Pin wrench with the (offset) angled head, same as the factory tool only this tool is a little longer for leverage with a rubber handle grip for a better feel compared to the smaller version.

Pin Wrench Angle Type 26.99

T10020 VW AUDI TENSION PULLEY SPANNER WRENCHThis unique tool is for 1998 and later VW and Audiwhich require spanner wrench adjustments to the timing belt.

Pin Wrench Set 2 49.00

This is the Best Quality Set of the two CRUCIAL VW Audi Pin Wrenches you will find anywhere.
SUPER HIGH QUALITY TOOLS (BOTH) MADE IN GERMANY BY HAZET.
First item is number V159 (this is a smaller tool on the left side picture is not to scale) This tool is for easy adjustment of Camshaft spur belts
(toothed belt) on idler pulleys with Pin holes. This wrench with its protruding pins, grabs the center
of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment.
Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80
Distance of pins 18 mm, diameter of pins 2.9 mm for deep located idler pulley
on toothed belt on 1,6 l diesel engine VW van T3 (up to model 1991).
V159 is the correct number the old VW Number on this (smaller) tool was 2587.

T10020 Special wrench with an offset (angled) head (Larger tool on right side of image)
This tool also used for adjusting timing belt tension.
99 and later VW Golf, VW Jetta and Beetle with 2.0 Litre Gas and 1.9 Litre TDI Engines.1999 and newer Golf, Jetta
New Beetle with 2.0l gas engine and 1.9l T.D.I. Diesel engine. You will get both tools with this purchase.

Puller, Pin , Plate , Holder , Pin Wrench 146.00

Set of five tools: vw 3032, VA6015 PLUS 2065A PLUS 2064 PLUS 12717
Details:
3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: Volvo and VW / Audi diesels Excluding TDI * PLUS: VA6015 Used for accurate adjustment of Bosch diesel injection pump. PLUS: 2065A Diesel Camshaft Locking Plate Tool PLUS: 2064 Lock Pin for Diesel. Plus the Pin Wrench (made in Germany) for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys with Pin holes. This wrench with its protruding pins, grabs the center of the idler pulley and rotates around the off center retaining bolt allowing for easy belt tension adjustment. Tension Pulleys on 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80.

RETAINER TOOLS 189.50

RETAINER TOOL SET USED TO HOLD THE THREE GROOVE V BELT PULLEY IN PLACE WHILE REMOVING AND INSTALLING. 2.1L ENGINES

Set 2 Sockets 22mm 34.99

Open Socket Plus Crowfoot Set
Both Tools are 22mm.
Details:
22mm (Open) TubeSocket (Number 4491A
1.) Used for securing the Strut tower retaining nut of most European models (crucial when adjusting tension of front shocks). The 2/3 open side walls of this socket allows for easy access of an adjusting wrench. (normally 7mm Allen Hex Wrench)2.) R&R of Oxygen Sensor.

Plus Oxygen Sensor Socket 4491b
This is a Special 22mm Crowsfoot Socket with 3/8 Drive
Used for the removal and replacement of Oxygen Sensors
situated within a confined area.
No need to snip the wires leading to the unit when all you want to do is check the sensor.
Applicable: Most European Models. Set of two tools.

Shift Linkage Guage 13.99

3104Shift Linkage Adjustment GuageFor adjusting shift linkage onJetta and Golf with 5 speed gear box.
Applicable: 1985 and newer.

Socket Plus Allen Wrench 34.99

2 Piece set 22mm Special Tube Socket 4491A plus 7mm Allen Wrench Used for securing the Strut tower retaining nut of most European models (crucial when adjusting tension of front shocks). The 2/3 open side walls of this socket allows for easy access of an adjusting wrench This socket can also be used for R&R of Oxygen Sensor. Plus You get an Angled 7mm Allen Wrench with handle.

Sockets plus Allen Set 3 38.99

Open Socket Plus Crowfoot Plus 7mm Allen
The Sockets are both 22mm.
Plus you get the long 7mm Allen Wrench
Details:
22mm (Open) TubeSocket (Number 4491A
1.) Used for securing the Strut tower retaining nut of most European models (crucial when adjusting tension of front shocks). The 2/3 open side walls of this socket allows for easy access of an adjusting wrench. (normally 7mm Allen Hex Wrench)2.) R&R of Oxygen Sensor.

Plus Oxygen Sensor Socket 4491b
This is a Special 22mm Crowsfoot Socket with 3/8 Drive
Used for the removal and replacement of Oxygen Sensors
situated within a confined area.
No need to snip the wires leading to the unit when all you want to do is check the sensor.
Applicable: Most European Models. Set of THREE tools.
Note: The Allen wrench is 7.5 inches long.

SPACER GUAGE 0.00

SPACER GUAGE FOR ADJUSTMENT OF THE BALL BEARING FOR THE INPUT SHAFT IN THE MANUAL GEARBOX

SPUR BELT SPREADER 72.50

FACTORY TOOL REQUIRED TO LOCK SPUR BELT SPROCKET ON ALL 4 CYLINDER WATERCOOLED INLINE VW ENGINES

T.D.I. Timing Kit 3 Tools 115.50

T.D.I. and New Beetle Cam Kit for correct and trouble free installations. Three crucial tools for changing timing belt on engine ALH. Chassis 1999 1/2 thru 2003 Golf Jetta (A4) MKIV and New Beetle TDI thru 2003.Reference numbers for the three tools are 3418 (Left side of image above) 3359 (Pin Center) and T10020 (Wrench Right)
This is a popular set for Diesel timing of Bosch injection pumps.This set has been developed for aligning the cam shaft with the Diesel pumpon 1998 and newer VW models equipped with a T.D.I. engine. Lock plate and alignment pin allows the technician for factory correctand trouble free installations.

TDC Pin T40026 24.99

Threaded Pin or Lock Bolt Tool used to secure crankshaft at T.D.C. during R&R of toothed timing belt, flywheel, drive plate, and crank bolt. Lock Bolt should be used in conjunction with Cam tools T40005.Check you manuals for details.

Tensioner 94.50

Original Tool 3191 Made in Germany REMOVE /INSTALL BELT TENSION DAMPER (G CHARGER ENGINES).

Threaded Pin for T.D.C. 25.00

Locking Pin
TOOL REF 3242
Crankshaft T.D.C. Lock Pin
Holds crankshaft at top dead center
T.D.C. Pin Applicable: A4 A6 Volkswagen Passat
Engine Applicable: Volkswagen AHA BDP ATQ BCY
Audi AAH AFC ATQ AHA AKB ART AUX BFM BHF
BNK BSB AVK AWN AYS BBD BCY & BEL
T.D.C. Pin Not Applicable 3.0 V6
For installing or removing toothed belt /flywheel drive plate.

Timing Kit Master Set 1 254.00

Serious Master Set: Description (for upper 3 tools) Timing belt on engine ALH. Chassis 1999 1/2 thru 2003 Golf Jetta (A4) MKIV and New Beetle TDI thru 2003.Reference numbers for the three tools are 3418 (Left side of image above) 3359 (Pin Center) and T10020 (Wrench Right. This is a popular set for Diesel timing of Bosch injection pumps. This set has been developed for aligning the cam shaft with the Diesel pumpon 1998 and newer VW models equipped with a T.D.I. engine.

BELOW IS THE DESCRIPTION ON THE LOWER 5 TOOLS. Five tools: vw 3032, 2066, 2065A, 2064 and 12717 (Pin Wrench) Details: 3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: VW / Audi diesels : 2066 Used for accurate adjustment of Bosch diesel injection pump. 2065A Diesel Camshaft Locking Plate Tool 2064 Lock Pin for Diesel. Pin Wrench 121717 Made in Germany for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys with Pin holes. This wrench with its protruding pins, grabs the center of idler pulley and rotates around the off center retaining bolt allowing for belt tension adjustment (Tension Pulleys) 4 cylinder Golf, Jetta, Passat and Corrado. Audi 80. You will get all 8 tools shown here.

You Searched for

Belt Tension Guage

Trade Links With ZDMAK